Winterizing terp fraction?

[_joe]

5 micron bag? Like a rosin bag attached to one of the tubes?

[DuhFinga]

What make fuge your baller pal have Vortal ?

[WhereAreTheStones]

Yes, folded over the top and secured with the lid.

[Dred_pirate]

It’s thca.

Both of these batters are a byproduct of the mechanical seperation.

[Dred_pirate]

And yes, you can winterize your HTE. And even in butane. I have even stated how to do it, somewhere in this metaverse of a website

[Strange]

Winterisation with butane possible?

You can have better results if you seperate the ht from the thca and process seperate. You shouldn’t decarb the terpenes, it can also make them taste worse. You can also winterize your ht in butane and a couple/few large Mason jars, it’s a little unorthodox, but you’ll save a lot more and better vs using alcohol and the roto evaporator, then decarb.

[vortal]

Did you test it? I gurantee that shit is like low 80’s at best, and the others are minors, tiny terps… And FAT. but whatever you say. Bout to run some live resin just to prove a point.

[Dred_pirate]

It’s a delicious batter.

[vortal]

I’m sure it is.

[ky_cbd]

Ah I’d recognize my kitchen counter and baby hands anywhere that top pic is CBD spun from ML btw not thca

[Dred_pirate]

Sorvall RC 3B Plus high capicity centrifuge

Often paired with the H6000A 6 x 1 liter rotor, or the kid brother H4000A 4 x 1 liter rotor

These are pretty tough

Sorvall RC-3B Plus High Capacity Centrifuge | GMI - Trusted Laboratory Solutions

[_joe]

Is that one of them 500$ fugues😂

[Dred_pirate]

Ain’t half bad for 10k with shipping. Pre tax

Sorvall RC-3B Refrigerated Centrifuge

[_joe]

Wow I figured it would be 15 easily

[vortal]

https://www.vikinglabsupply.com/product/viking-glassworks-50ml-x-6-site-centrifuge-4000rpm/

This one will spin a half pound easy.

[Dred_pirate]

You can only fill them halfway-ish to spin off hte before it becomes too much in each one

[Dred_pirate]

https://www.amazon.com/Centrifuge-DEJUN-Centrifuges-Laboratory-Centrifugal/dp/B08VFX4TNV/ref=mp_s_a_1_1?crid=2ZL2792U1XWPC&keywords=4x100ml+centrifuge&qid=1637937973&qsid=131-1125216-8140709&sprefix=4x100ml+centrifuge+%2Caps%2C156&sr=8-1&sres=B08VFX4TNV%2CB00V4BE0U0%2CB009G6X5I8%2CB005GRFWFK%2CB07SNGPVKR%2CB009G6XOCK%2CB005GRFQBA%2CB00VT67NGS%2CB00NG263MI%2CB07ZFK4L22%2CB07JGPZYHF%2CB07CTBHQZK%2CB017VTRJPG%2CB07H9DJD78

This is the “standard” 4x100ml that is used

[vortal]

I use those two pictures to push spinning to the local gang quick and dirty examples. Consider yourself a legend. <3

[_joe]

Like 150g they hatch hold about 27g

[WhereAreTheStones]

@vortal

Did you test it? I gurantee that shit is like low 80’s at best, and the others are minors, tiny terps… And FAT. but whatever you say. Bout to run some live resin just to prove a point.

We see this on dry material as well, not just fresh frozen. What you’re seeing stuck at the bottom is almost pure thca. You may have some fats present if you scrape up the tiny bit of hte with it. I’m sure they’re still present in the hte you poured off as well.