Anyone try a Chinese centrifuge ?

CannaBusiness
, ,
22

Ptfe gasket I was told. $1500 by air, $200-300 ocean.

1 Like
24

Hello,dear
We are the China supplier
Thanks for knowing that you are in the industry and looking for the supplier.
We have sold a large number of it for USA and other country.

And now,we have completed the whole line for extracting oil.
So,if you have interests about it and want to know more about it,
pls kindly inform me.

My online contact is +86 19951199985 (office number),
or you can send me email : centrifuges@vip.sina.com

Waiting for your message.

Anita yuen

25

Hello,Paragon Engineering?

I’m Jim, I ever invited you to visit my Peony factory.
And how are you recently?Hope everything well!:grinning:

Actually, Peony and Kingreat are the same group,we just use the different types to promote.
So i just clarify it with you.

And if have the chance，we can restart to talk about it.

My online contact is +86 19951199985 (office number),
or you can send me email : [centrifuges@vip.sina.com]

Waiting for your message.

26

Hey Jim, thx for coming aboard the canna-Cruise! Can u send us some pictures and specs of your latest jacketed centrifuges.?Also, we would like to see the unit being chilled and spinning with ethanol inside. Most buyers here in US are concerned about the seals and how well they hold up exposed to solvents and cold temps.

27

PTFE gaskets for hexane compatibility? How about a 2" thick sleeve for loading the outer sleeve with dry ice, not a jacket for recirculation

2 Likes
28

Here’s the specs on the unit:

image
image926×418 188 KB

I’ll be ordering from lanphan as they offered it cheaper than 5k.

3 Likes
29

the 1500rpm scares me since I am used to the Panda spin dryers spinning at 3200rpm(U believe)

is the 1500rpm good enough for most people? I am getting ready to pull the trigger on a centrifuge soon.

30

That is smaller diameter and slower speed than the one @Paragon1 posted FYI.
less G’s to get that solvent out

32

I don’t see where he posted the specs anywhere in this thread. Can you post them please?

33

1500rpm on one of these loaded to capacity is very likely to scare you.

but does a decent job at removing residuals, similar to one I used to run would get it nearly dry…
but that was before I realized I was running with the top feeds open, thus creating a huge air dryer lol filling the room with fumes every time I ran and making the waste seem dryer than the spinning was actually accomplishing
WORLDS better than a panda. but scary at times lol, don’t overclock them.

1 Like
34

They’re not in this thread. He DM’ed me the specs. Get in touch with him.

1 Like
35

8kg dry mass
1900rpm
Controller cabinet
Motor is UL listed
Control Cabinet is not

2 Likes
36

450mm diameter
1900rpm
1816.191 gforce

1 Like
37

Hello! So are you Paragon Engineering?Right?

The seals are used the same material with AFAL LAVAL,but we can’t guarantee that it will always be effective, so we recommend that it be replaced regularly,and we may provide some seals for reserve.

In addition, we have been improving the sealing problem.With regard to technical issues, I hope we can communicate further by email.

Waiting for your email.
Tel: +86 19951199985 (office number),
Email : [centrifuges@vip.sina.com]

38

Id be in at 5k. That’s not bad at all.

1 Like
39

I’m also interested in this unit ASAP!

40

I’m curious how one fits 8kg/17.6lbs of dry biomass in a 25L/6.58Gal basket. Does that seem right?

42

Anyone get one of these?

43

i am manufacturer from China and now there is a new type jacketed centrifuge.
pls see this link of my post and you could see more.

if you want more details, just DM me and i will send all models to u.

https://future4200.com/t/new-centerfugal-alcohol-extractor-from-manufacturer/32133

44

Is anyone in China making an open sleeved dry ice loadable centrifuge?

2 Likes